Do VLANs within a subnet need to have their own subnet for router on a stick?
I have been creating a network lab in packet tracer for practice. I have 3 vlans in subnet A and I am trying to configure router on a stick at gig6/0 on the bottom left of the image. Do I need to create a subnet for each VLAN in order for the router on a stick gateway to work?
router vlan subnet trunk gateway
edited Apr 6 at 19:04
Cown
6,96631031
asked Apr 6 at 16:00
Jon StinnettJon Stinnett
111
New contributor
Jon Stinnett is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
add a comment |
I have been creating a network lab in packet tracer for practice. I have 3 vlans in subnet A and I am trying to configure router on a stick at gig6/0 on the bottom left of the image. Do I need to create a subnet for each VLAN in order for the router on a stick gateway to work?
router vlan subnet trunk gateway
edited Apr 6 at 19:04
Cown
6,96631031
asked Apr 6 at 16:00
Jon StinnettJon Stinnett
111
New contributor
Jon Stinnett is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
add a comment |
I have been creating a network lab in packet tracer for practice. I have 3 vlans in subnet A and I am trying to configure router on a stick at gig6/0 on the bottom left of the image. Do I need to create a subnet for each VLAN in order for the router on a stick gateway to work?
router vlan subnet trunk gateway
edited Apr 6 at 19:04
Cown
6,96631031
asked Apr 6 at 16:00
Jon StinnettJon Stinnett
111
New contributor
Jon Stinnett is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
I have been creating a network lab in packet tracer for practice. I have 3 vlans in subnet A and I am trying to configure router on a stick at gig6/0 on the bottom left of the image. Do I need to create a subnet for each VLAN in order for the router on a stick gateway to work?
router vlan subnet trunk gateway
router vlan subnet trunk gateway
edited Apr 6 at 19:04
Cown
6,96631031
asked Apr 6 at 16:00
Jon StinnettJon Stinnett
111
New contributor
Jon Stinnett is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
edited Apr 6 at 19:04
Cown
6,96631031
asked Apr 6 at 16:00
Jon StinnettJon Stinnett
111
New contributor
Jon Stinnett is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
edited Apr 6 at 19:04
Cown
6,96631031
edited Apr 6 at 19:04
Cown
6,96631031
edited Apr 6 at 19:04
Cown
6,96631031
6,96631031
asked Apr 6 at 16:00
Jon StinnettJon Stinnett
111
New contributor
Jon Stinnett is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked Apr 6 at 16:00
Jon StinnettJon Stinnett
111
asked Apr 6 at 16:00
Jon StinnettJon Stinnett
111
111
New contributor
Jon Stinnett is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
New contributor
Jon Stinnett is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
Jon Stinnett is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
add a comment |
add a comment |
2 Answers
2
active
oldest
votes
I'm not understanding your exact problem because you don't provide enough detail but maybe this helps:
With rare exceptions, an IP subnet is mapped to a VLAN = broadcast domain = layer-2 network on a 1:1 basis.
You can run multiple IP subnets inside a single VLAN but they need a router to communicate with each other. Most often this setup doesn't make too much sense.
You can't run a single IP subnet across multiple VLANs though (without elaborate workarounds). Nodes in the same subnet expect to be able to talk to each other on a common layer-2 network = VLAN = broadcast domain.
So, your "VLANs within a subnet" can only work when you've split that subnet into sub-subnets properly and set up the router as gateway in between. A router on a stick is a router forwarding between VLAN subinterfaces on a single physical interface. Each subinterface needs to connect to one of the desired VLANs, so the link needs to be a VLAN trunk on both the switch and the router side.
answered Apr 6 at 16:41
Zac67Zac67
32.7k22164
add a comment |
Just to amplify on Zac’s answer: you have one subnet per vlan and vice versa. At the CCNA level, you can ignore the rare exceptions. The router on a stick has an (sub)interface in each subnet. Therefore all VLANs must be trunked to the router.
edited Apr 6 at 19:03
Cown
6,96631031
answered Apr 6 at 16:48
Ron TrunkRon Trunk
39.6k33780
add a comment |
Your Answer
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "496"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
noCode: true, onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
Jon Stinnett is a new contributor. Be nice, and check out our Code of Conduct.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fnetworkengineering.stackexchange.com%2fquestions%2f58283%2fdo-vlans-within-a-subnet-need-to-have-their-own-subnet-for-router-on-a-stick%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
2 Answers
2
active
oldest
votes
2 Answers
2
active
oldest
votes
active
oldest
votes
active
oldest
votes
I'm not understanding your exact problem because you don't provide enough detail but maybe this helps:
With rare exceptions, an IP subnet is mapped to a VLAN = broadcast domain = layer-2 network on a 1:1 basis.
You can run multiple IP subnets inside a single VLAN but they need a router to communicate with each other. Most often this setup doesn't make too much sense.
You can't run a single IP subnet across multiple VLANs though (without elaborate workarounds). Nodes in the same subnet expect to be able to talk to each other on a common layer-2 network = VLAN = broadcast domain.
So, your "VLANs within a subnet" can only work when you've split that subnet into sub-subnets properly and set up the router as gateway in between. A router on a stick is a router forwarding between VLAN subinterfaces on a single physical interface. Each subinterface needs to connect to one of the desired VLANs, so the link needs to be a VLAN trunk on both the switch and the router side.
answered Apr 6 at 16:41
Zac67Zac67
32.7k22164
add a comment |
I'm not understanding your exact problem because you don't provide enough detail but maybe this helps:
With rare exceptions, an IP subnet is mapped to a VLAN = broadcast domain = layer-2 network on a 1:1 basis.
You can run multiple IP subnets inside a single VLAN but they need a router to communicate with each other. Most often this setup doesn't make too much sense.
You can't run a single IP subnet across multiple VLANs though (without elaborate workarounds). Nodes in the same subnet expect to be able to talk to each other on a common layer-2 network = VLAN = broadcast domain.
So, your "VLANs within a subnet" can only work when you've split that subnet into sub-subnets properly and set up the router as gateway in between. A router on a stick is a router forwarding between VLAN subinterfaces on a single physical interface. Each subinterface needs to connect to one of the desired VLANs, so the link needs to be a VLAN trunk on both the switch and the router side.
answered Apr 6 at 16:41
Zac67Zac67
32.7k22164
add a comment |
I'm not understanding your exact problem because you don't provide enough detail but maybe this helps:
With rare exceptions, an IP subnet is mapped to a VLAN = broadcast domain = layer-2 network on a 1:1 basis.
You can run multiple IP subnets inside a single VLAN but they need a router to communicate with each other. Most often this setup doesn't make too much sense.
You can't run a single IP subnet across multiple VLANs though (without elaborate workarounds). Nodes in the same subnet expect to be able to talk to each other on a common layer-2 network = VLAN = broadcast domain.
So, your "VLANs within a subnet" can only work when you've split that subnet into sub-subnets properly and set up the router as gateway in between. A router on a stick is a router forwarding between VLAN subinterfaces on a single physical interface. Each subinterface needs to connect to one of the desired VLANs, so the link needs to be a VLAN trunk on both the switch and the router side.
answered Apr 6 at 16:41
Zac67Zac67
32.7k22164
I'm not understanding your exact problem because you don't provide enough detail but maybe this helps:
With rare exceptions, an IP subnet is mapped to a VLAN = broadcast domain = layer-2 network on a 1:1 basis.
You can run multiple IP subnets inside a single VLAN but they need a router to communicate with each other. Most often this setup doesn't make too much sense.
You can't run a single IP subnet across multiple VLANs though (without elaborate workarounds). Nodes in the same subnet expect to be able to talk to each other on a common layer-2 network = VLAN = broadcast domain.
So, your "VLANs within a subnet" can only work when you've split that subnet into sub-subnets properly and set up the router as gateway in between. A router on a stick is a router forwarding between VLAN subinterfaces on a single physical interface. Each subinterface needs to connect to one of the desired VLANs, so the link needs to be a VLAN trunk on both the switch and the router side.
answered Apr 6 at 16:41
Zac67Zac67
32.7k22164
edited Apr 6 at 21:04
answered Apr 6 at 16:41
Zac67Zac67
32.7k22164
answered Apr 6 at 16:41
Zac67Zac67
32.7k22164
answered Apr 6 at 16:41
Zac67Zac67
32.7k22164
32.7k22164
add a comment |
add a comment |
Just to amplify on Zac’s answer: you have one subnet per vlan and vice versa. At the CCNA level, you can ignore the rare exceptions. The router on a stick has an (sub)interface in each subnet. Therefore all VLANs must be trunked to the router.
edited Apr 6 at 19:03
Cown
6,96631031
answered Apr 6 at 16:48
Ron TrunkRon Trunk
39.6k33780
add a comment |
Just to amplify on Zac’s answer: you have one subnet per vlan and vice versa. At the CCNA level, you can ignore the rare exceptions. The router on a stick has an (sub)interface in each subnet. Therefore all VLANs must be trunked to the router.
edited Apr 6 at 19:03
Cown
6,96631031
answered Apr 6 at 16:48
Ron TrunkRon Trunk
39.6k33780
add a comment |
Just to amplify on Zac’s answer: you have one subnet per vlan and vice versa. At the CCNA level, you can ignore the rare exceptions. The router on a stick has an (sub)interface in each subnet. Therefore all VLANs must be trunked to the router.
edited Apr 6 at 19:03
Cown
6,96631031
answered Apr 6 at 16:48
Ron TrunkRon Trunk
39.6k33780
Just to amplify on Zac’s answer: you have one subnet per vlan and vice versa. At the CCNA level, you can ignore the rare exceptions. The router on a stick has an (sub)interface in each subnet. Therefore all VLANs must be trunked to the router.
edited Apr 6 at 19:03
Cown
6,96631031
answered Apr 6 at 16:48
Ron TrunkRon Trunk
39.6k33780
edited Apr 6 at 19:03
Cown
6,96631031
edited Apr 6 at 19:03
Cown
6,96631031
edited Apr 6 at 19:03
Cown
6,96631031
6,96631031
answered Apr 6 at 16:48
Ron TrunkRon Trunk
39.6k33780
answered Apr 6 at 16:48
Ron TrunkRon Trunk
39.6k33780
answered Apr 6 at 16:48
Ron TrunkRon Trunk
39.6k33780
39.6k33780
add a comment |
add a comment |
Jon Stinnett is a new contributor. Be nice, and check out our Code of Conduct.
Jon Stinnett is a new contributor. Be nice, and check out our Code of Conduct.
Jon Stinnett is a new contributor. Be nice, and check out our Code of Conduct.
Jon Stinnett is a new contributor. Be nice, and check out our Code of Conduct.
Thanks for contributing an answer to Network Engineering Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fnetworkengineering.stackexchange.com%2fquestions%2f58283%2fdo-vlans-within-a-subnet-need-to-have-their-own-subnet-for-router-on-a-stick%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
